;******************** DEVICE and FILE INFORMATION ********************* ;* * ;* FILE NAME: TES_0A8A.GSD * ;* DEVICE TYPE: PROFIBUS-PA * ;* DEVICE INFORMATION: T6680 * ;* PROFILE COMPATIBILITY: PROFILE 3.01 * ;********************** GSD REVISION INFORMATION ********************** ;* $Revision: 1.1 $ * ;* $Date: 2007/10/19 09:41:08Z $ * ;* * ;* DATE d.m.j | NAME | VERSION | COMMENT * ;* ---------------------------------------------------------------------- * ;* 10.10.2006 | | 1.0 | initial revision * ;************************************************************************** #Profibus_DP GSD_Revision = 5 Vendor_Name = "Testo AG" Model_Name = "Testo 6680" Revision = "1.0" Ident_Number = 0x0A8A Protocol_Ident = 0 Station_Type = 0 FMS_supp = 0 Hardware_Release = "V1.0" Software_Release = "V1.0" Bitmap_Device = "TES_0A8A" 9.6_supp = 1 19.2_supp = 1 45.45_supp = 1 93.75_supp = 1 187.5_supp = 1 500_supp = 1 1.5M_supp = 1 3M_supp = 1 6M_supp = 1 12M_supp = 1 MaxTsdr_9.6 = 15 MaxTsdr_19.2 = 15 MaxTsdr_45.45 = 15 MaxTsdr_93.75 = 15 MaxTsdr_187.5 = 15 MaxTsdr_500 = 15 MaxTsdr_1.5M = 25 MaxTsdr_3M = 50 MaxTsdr_6M = 100 MaxTsdr_12M = 200 Redundancy = 0 Repeater_Ctrl_Sig = 0 24V_Pins = 0 Implementation_Type = "SPC3" Freeze_Mode_supp = 0 Sync_Mode_supp = 0 Set_Slave_Add_supp = 1 Min_Slave_Intervall = 6 Modular_Station = 1 Max_Module = 2 Max_Input_Len = 10 ; maximum Input Length Max_Output_Len = 0 ; maximum Output Length Max_Data_Len = 10 ; maximum In-Output Length Slave_Family = 12 Max_Diag_Data_Len = 20 Max_User_Prm_Data_Len = 3 Ext_User_Prm_Data_Const(0) = 0x00, 0x00, 0x00 ;----------- Description of extended DP features: --------------------- ; DPV1_Slave = 1 C2_Read_Write_supp = 1 C2_Max_Data_Len = 128 C2_Read_Write_required = 1 C2_Max_Count_Channels = 2 Max_Initiate_PDU_Length = 52 C2_Response_Timeout = 4000 DPV1_Data_Types = 1 Ident_Maintenance_supp = 1 ;---- Description of physical interface for asynchronous transmission: ---- ; RS485 Standard Copper can be selected without additional restrictions. ;----------- Description of device related diagnosis: --------------------- ; Unit_Diag_Bit(16) = "Error appears" Unit_Diag_Bit(17) = "Error disappears" Unit_Diag_Bit(36) = "Coldstart" Unit_Diag_Bit(55) = "Extension Available" ;------------------------------------------------------------------------- ; ;----------- Description of device related extended diagnosis: ----------- Unit_Diag_Area=56-63 Value(0) = "No Error" Value(1) = "MUF" Value(2) = "Probe" Unit_Diag_Area_End Unit_Diag_Area = 64-71 Value(0) = "No Error" Value(1) = "Information" Value(2) = "Warning" Value(3) = "Error" Unit_Diag_Area_End Unit_Diag_Area = 72-79 Value(0) = "No Error" Value(1) = "Measure" Value(2) = "Adjust" Value(3) = "Service" Value(4) = "Configuration" Value(5) = "Communication" Value(6) = "System" Value(7) = "Environment" Value(8) = "non specific" Unit_Diag_Area_End Unit_Diag_Area = 80-87 Value(0) = "No Error" Value(5) = "Limit value changed" Value(6) = "Scaling changed" Value(7) = "Reset executed" Value(8) = "Probe disconnected" Value(9) = "Drift 2point adjust" Value(10) = "Ambient temp high" Value(11) = "Ambient temp low" Value(12) = "Supply voltage low" Value(13) = "No communication" Value(14) = "No probe signal" Value(15) = "Wrong probe" Value(16) = "Watchdog error" Value(17) = "Sensor refresh active" Value(18) = "1 point adjust" Value(19) = "2 point adjust 11,3%" Value(20) = "2 point adjust 75,3%" Value(21) = "3rd adjustment point" Value(22) = "Self adjust active" Value(23) = "Medium temp high" Value(24) = "Start of condensation" Value(25) = "Values below 0%" Value(26) = "Cover electrode warning" Value(27) = "Humidity sensor short circuit" Value(28) = "Humidity sensor broken" Value(29) = "T sensor short circuit" Value(30) = "T sensor broken" Value(31) = "Error self adjustment" Value(32) = "Probe reset" Unit_Diag_Area_End ;------------------------------------------------------------------------- ; ;Empty module Module = "Empty Module" 0x00 1 EndModule ; ;Modules for Analog Input Module = "Analog Input (AI)short" 0x94 2 EndModule ;Modules for Analog Input Module = "Analog Input (AI)long" 0x42,0x84,0x08,0x05 3 EndModule ;----------- Description of the module assignment: --------------------- ; SlotDefinition Slot(1) = "Analog Input" 2 1,2,3 Slot(2) = "Analog Input" 2 1,2,3 EndSlotDefinition